Kubota D1105-E3B Troubleshooting
| Engine Model: Kubota D1105-E3B |
| Engine Type: 4-cycle vertical 3-cylinder liquid-cooled diesel |
| Total Displacement: 68.6 cu.in (1.12 L) |
| Rated Engine Power: 24.8 Hp (18.5 kW) at 3000 rpm |
| Aspiration Type: Naturally aspirated |
____________________________________________________________________________________
| Engine difficult to start or will not start |
Fuel filter element clogging - Service the filter.
Air in fuel system - Bleed fuel system.
Fuel injection nozzles are clogged or faulty - Inspect nozzles and replace if necessary.
Fuel injection pump damage - Change pump or rebuild it.
Unadjusted valve timing - Correct or change timing gear.
Dirt in the fuel lines or hoses - Service or replace fuel pipes.
Unadjusted injection timing - Adjust according to specifications.
Cylinder or piston rings are worn - Change faulty parts.
| Engine starts and stops suddenly |
Fuel filter element is clogged - Change filter element.
Fuel injection pump is defective - Repair or replace injection pump.
Clogged air filter - Clean or change.
Nozzle opening pressure is improper - Adjust as recommended.
| Engine shuts off suddenly during operation |
Wrong setting of fuel injection pump timing - Set up as recommended.
Fuel filter element is dirty - Service the filter.
Engine is cold - Warm up engine as required.
Injection nozzles are stuck or clogged - Check injection nozzles and replace if required.
| Engine stalls while idling |
Improperly adjusted low idle speed - Adjust low idling as recommended.
Valve clearance is wrong - Correct valve clearance needs to be set.
Fuel injection pump malfunctioning - Repair or install a new fuel pump.
Defective or clogged injection nozzle - Replace injection nozzles.
Dirt in the fuel lines or hoses - Clean fuel system lines and hoses.
Air filter is clogged - Install new air filter element.
Cylinder head gasket is worn - Replace the gasket as required.
Unadjusted injection timing - Check injection timing adjustment.
Fuel injection pump is damaged - Repair or install a new fuel pump.
One of moving engine components is worn - Replace or repair damaged components.
Damaged radiator cap or dirty radiator core - Clean radiator or install new cap.
Insufficient coolant - Fill the cooling system and check components for leaks or other faults.
Damaged or worn fan belt - Fan belt must be replaced.
Engine oil level is insufficient - Check oil level and add oil as required.
Blown cylinder head gasket - Install a new gasket.
Wrong injection timing - Adjust injection timing as required.
Low crankcase oil level - Checking oil level and add if necessary.
Oil pump is worn or damaged - Replace as required.
Oil filter element clogging - Clean or replace engine oil filter element.
Stuck or worn relief valve - Change or service relief valve.
Excessive crankshaft bearing clearance - Test and repair or replace worn parts.
Excessive crankpin bearing clearance - Test and repair or replace worn parts.
| Engine using too much oil |
Oil leaking: Seals or gaskets are defective - To repair leaks, replace worn parts.
Crankcase oil too light - Use oil of proper viscosity.
Worn or broken piston rings - Change the piston rings as required.
Valve stems and guides are worn - Install new valves.
Pistons or cylinder liners are damaged - Check liners and pistons, install new components as required.
| Engine knocking sound or abnormal noise |
Low coolant temperature - Warm up the engine.
Low engine oil level - Fill up the engine oil.
Timing of fuel injection pump is incorrect - Set up as recommended.
Broken or worn pistons - Install new pistons.
Misaligned or defective connecting rod - Connecting rod needs to be aligned or changed.
Low battery output voltage - Charge the battery.
Battery runs out quickly - Service charging system or change battery.
Bad terminals or disconnected battery cables - Connect wires correctly or change terminals.
Battery is low or faulty - Charge or change the battery.
Wiring is improperly connected or disconnected - Check wiring and connect properly.
Battery power is low - Recharge the battery.
Starter motor failure - Replace or repair starter.
____________________________________________________________________________________
| Industrial Engines Technical Specifications |
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Outboard Engines Technical Specifications |
