Honda GX110 Troubleshooting
| Engine Model: Honda GX110 |
| Engine Type: 4-cycle single-cylinder OHV air-cooled gasoline |
| Total Displacement: 6.5 cu.in (107 cc) |
| Rated Engine Power: 3.5 Hp (2.6 kW) at 3600 rpm |
| Carburetor Type: Horizonal with butterfly valve |
____________________________________________________________________________________
| Engine won't start or difficult to start |
Empty fuel tank - Add fuel.
Wrong fuel grade - Use correct fuel grade.
Water or air in fuel system - Remove air or water from system.
Spark plug wiring connection is damaged - Check spark plug wiring connection, repair or change.
Spark plug is faulty - Change spark plug.
Plugged fuel filter - Fuel filter needs to be replaced.
Safety contact for brake pedal defective - Install new part.
Carburetor is clogged - Clean the carburetor.
Bad compression - Check and change damaged parts.
Damaged or not adjusted choke cable - Adjust properly or change the cable.
Clogged cooling fins - Need to clean or wash.
Ignition system is defective - Inspect ignition system and change failed components.
Choke cable is stuck or faulty - Clean or change the cable.
Air filter is blocked - Replace or service air filter.
Fuel pump is clogged or faulty - Test fuel pump and replace if necessary.
| Engine starts and stops suddenly |
Spark plug is damaged - Spark plug need to be replaced.
Carburetor is defective or clogged - Clean or replace carburetor.
Defective ignition coil - Ignition coil should be replaced.
Bad or damaged valve springs - Install new valve springs.
Valves are stuck - Clean the valves.
Low engine oil level - Add oil to the engine crankcase.
Engine overload - Reduce engine load.
Clogged cooling fins - Need to clean or wash.
Carburetor mixture is too lean - Set the carburetor properly.
Wrong ignition timing - Adjust ignition timing as required.
Valve setting is wrong - Adjust valves as required.
Low octane fuel - Use proper gasoline.
Engine overloaded - Reduce load.
Engine oil insufficient - Fill the crankcase with engine oil.
Low idle speed setting is incorrect - Correct idle adjustment.
Clogged or defective fuel pump - Service or replace fuel pump.
Main bearings or crankshaft failure - Have bearings or crankshaft replaced.
Valve clearance is not correct - Adjust valve clearance.
Worn piston rings or cylinder bore - Change faulty components.
Carburetor is dirty or incorrectly adjusted - Clean or correctly adjust carburetor.
Air filter element is plugged - Service or replace air filter.
Fuel pump is faulty or clogged - Test fuel pump and replace if necessary.
Defective ignition system - Inspect ignition system and change faulty parts.
Cylinder head gasket is defective - Replace the head gasket.
Valves are stuck or burned - Clean or replace valves.
Worn or defective push rod - Push rod should be replaced.
Cylinder block parts are worn out - Replace defective components as required.
Oil filter element is plugged (if equipped) - Clean or replace oil filter.
Choke is not fully open - Check choke cable and adjust it.
Improper adjustment of carburetor main jet - Adjust it properly.
Loose or defective spark plug - Re-tighten or change the spark plug.
Burned, worn, or stuck valves - Change or service valves.
Piston, sleeve, or rings are damaged - Change defective components.
Valve clearance is not correct - Need to adjust valve clearance.
| High engine oil consumption |
Defective seals or gaskets - Change worn parts according to specifications.
Valve guides or stems are damaged - Valves must be replaced.
Stuck or defective piston rings - Piston rings replacement required.
Piston or cylinder liner is damaged - Check liner and piston, replace as required.
Breather pipe or hose is clogged - Clean or replace.
____________________________________________________________________________________
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Outboard Engines Technical Specifications |
| Industrial Engines Technical Specifications |
