____________________________________________________________________________________
| Home / Small Engines / Honda Engines / Honda GV100 |
Honda GV100 Troubleshooting
| Engine Model: Honda GV100 |
| Engine Type: 4-cycle 1-cylinder air-cooled gasoline engine |
| Total Displacement: 5.9 cu.in (97 cc) |
| Rated Engine Power: 2.6 Hp (1.9 kW) at 4200 rpm |
| Carburetor Type: Horizonal, butterfly valve |
____________________________________________________________________________________
| Engine won't start or difficult to start |
Fuel tank is empty - Fill gasoline up.
Incorrect fuel grade - Use quality gasoline.
Air in the fuel pipes - Bleed the fuel pipes.
Damaged spark plug wiring connection - Check the spark plug wire connection, repair or replace.
Faulty spark plug - Install new spark plug.
Clogged fuel filter - Fuel filter needs changing.
Brake pedal not depressed - Press the brake pedal.
Wrong carburetor adjustment - Adjusting carburetor correctly.
Bad engine compression - Inspect cylinder block and replace worn components.
Choke cable is worn or not adjusted properly - Adjust properly or replace the cable.
| Engine runs intermittently |
Air intake screen is blocked - Clean and wash as required.
Ignition system is defective - Inspect ignition system and change failed components.
Faulty or stuck choke cable - Clean or replace the cable.
Air filter is dirty - Replace or service air filter.
Fuel pump is clogged or faulty - Clean or replace fuel pump.
| Engine stalls after starting |
Damaged spark plug - Replace spark plug.
Dirty or faulty carburetor - Service or replace carburetor.
Ignition coil is faulty - Ignition coil must be replaced.
Broken or loose valve springs - Valve springs need to be changed.
Stuck valves - Clean the valves.
| Engine keeps overheating |
Lack of engine oil - Fill up the engine oil.
Engine overload - Load reducing required.
Cooling fins are blocked - Wash or clean as required.
Carburetor fuel mixture is too lean - Set the carburetor correctly.
Incorrect ignition timing - Adjust ignition timing correctly.
Valve setting is wrong - Valves needs to be adjusted properly.
| Engine noise or knocking |
Low octane gasoline - Use correct gasoline.
Engine is under excessive load - Load reducing is recommended.
Engine oil level is low - Fill the crankcase with engine oil.
Incorrect low idle setting - Correct the settings.
Clogged or defective fuel pump - Service or replace fuel pump.
Crankshaft or main bearings failure - Install new parts as as required.
Valve clearance is incorrect - Adjust valve clearance.
Piston rings or cylinder bore are worn - Change faulty parts.
| Engine power loss |
Incorrectly adjusted or clogged carburetor - Service or properly adjust carburetor.
Air filter element is plugged - Replace or service air filter.
Clogged or defective fuel pump - Service or replace fuel pump.
Ignition system failure - Check ignition and replace faulty components.
Worn cylinder head gasket - Install new cylinder head gasket.
Burned or stuck valves - Replace or service valves.
Push rod is damaged or worn - Replace push rod.
Cylinder block parts are worn out - Change defective parts.
Oil filter element is clogged (if equipped) - Clean or replace oil filter.
| High fuel consumption |
Choke is not fully open - Check choke cable and adjust it.
Incorrect adjustment of carburetor main jet - Adjust it correctly.
Spark plug is faulty or loose - Tighten or replace spark plug.
Worn, stuck, or burned valves - Clean or change valves.
Sleeve, rings, or piston are damaged - Replace faulty components as required.
Valve clearance is not correct - Adjustment procedure required.
| Engine using too much oil |
Gaskets or seals can be faulty - Replace to repair leaks.
Valve stems and guides are worn - Replace defective valves.
Worn or stuck piston rings - Piston rings replacement required.
Cylinder liner or piston is scored - Inspect piston and liner, fit new components as necessary.
Breather hose or pipe is blocked - Clean or change.
____________________________________________________________________________________