Honda G50 Troubleshooting
| Engine Model: Honda G50 |
| Engine Type: 4-cycle 1-cylinder horizontal shaft air-cooled gasoline |
| Total Displacement: 11.4 cu.in (187 cc) |
| Rated Engine Power: 4.9 Hp (3.65 kW) at 4000 rpm |
| Carburetor Type: Horizontal with butterfly valve |
____________________________________________________________________________________
| Engine doesn't start or difficult to start |
Gas tank is empty - Fill gasoline up.
Wrong fuel grade - Change gasoline.
Air or water in fuel system - Remove water or air from fuel system.
Spark plug wire is disconnected or loose - Inspect spark plug wiring connection, change or repair.
Defective spark plug - Change spark plug.
Fuel filter is dirty - Replace fuel filter.
Brake pedal not depressed - Press the brake pedal.
Carburetor is not adjusted - Check carburetor float adjustment.
Poor engine compression - Check cylinder block and replace damaged components.
Throttle cable is damaged or adjusted incorrectly - Change cable or adjust correctly.
Air intake screen is plugged - Wash or clean as required.
Ignition system problems - Inspect ignition system and change faulty parts.
Choke cable is faulty or stuck - Change or service the cable.
Air filter element is plugged - Clean or replace air filter.
Clogged or damaged fuel pump - Inspect fuel pump and change as required.
| Engine starts but then stops |
Spark plug is faulty - Spark plug need to be replaced.
Carburetor is clogged or faulty - Clean or change carburetor.
Damaged ignition coil - Replace ignition coil as necessary.
Valve springs are bad or broken - New valve springs need to be installed.
Valves sticking - Valves must be cleaned.
Low engine oil level - Fill up the engine oil.
Engine is under excessive load - Reduce load.
Clogged cooling fins - Need to wash or clean.
Too lean carburetor mixture - Adjust carburetor correctly.
Ignition timing is incorrect - Adjust ignition timing correctly.
Valve setting is wrong - Set the valves correctly.
Stale fuel - Change fuel.
Engine is running overloaded - Reduce the load.
Low engine oil level - Need to add engine oil.
Incorrectly adjusted low idle speed - Adjust idle speed.
Fuel pump is damaged or dirty - Inspect fuel pump and change as required.
Main bearings or crankshaft are worn out - Replace crankshaft or bearings.
Valve clearance is not correct - Adjustment procedure required.
Piston rings or cylinder bore are worn - Replace defective components.
Carburetor is dirty or incorrectly adjusted - Service or properly adjust carburetor.
Air filter element is plugged - Change or clean air filter.
Fuel pump is damaged or dirty - Service or replace fuel pump.
Ignition system problems - Test ignition and replace failed parts.
Worn cylinder head gasket - Install new head gasket.
Stuck or burned valves - Service or replace valves.
Push rod is worn or bent - Change push rod.
Cylinder block parts are damaged - Change defective parts.
Oil filter element is plugged (if equipped) - Replace or service oil filter.
| Engine uses too much fuel |
Choke opening is not full - Replace or adjust choke cable.
Carburetor main jet adjustment is improper - Adjust it correctly.
Loose or faulty spark plug - Tighten or replace spark plug.
Worn, stuck, or burned valves - Replace or service valves.
Worn sleeve, piston, or rings - Replace faulty components.
Valve clearance is wrong - Check and adjust.
| Engine oil consumption is too high |
Seals or gaskets are defective - Worn parts need to be replaced.
Valve guides or stems are damaged - Valves must be replaced.
Stuck or defective piston rings - Install new piston rings.
Piston or cylinder liner is worn - Inspect liner and piston, replace as necessary.
Plugged breather hose or pipe - Service or change.
____________________________________________________________________________________
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Outboard Engines Technical Specifications |
| Industrial Engines Technical Specifications |
