Mariner 225 Super Magnum problems
| Engine Model: Mariner Super Magnum 225 Hp |
| Engine Type: 2-stroke 6-cylinder gasoline outboard engine |
| Total Displacement: 153 cu.in (2507 cc) |
| Rated Engine Power: 225 Hp (167.9 kW) at 6500 rpm |
| Fuel System: Electronic fuel injection (EFI) |
____________________________________________________________________________________
| Engine won't start or difficult to start |
Empty fuel tank - Add gasoline.
Wrong grade of gasoline - Change gasoline.
There is air in the fuel system - Bleed the system.
Loose or disconnected spark plug wire - Check the spark plug wire connection, repair or replace.
Faulty spark plug - Spark plug need to be replaced.
Clogged fuel filter - Replace or clean fuel filter.
Fuel lines are clogged - Clean fuel system lines.
Discharged or faulty battery - Need to charge or replace the battery.
Damaged electrical wire harness - Inspect harness connections.
Ignition system malfunction - Replace defective components.
Pulse fuel pump is defective - Change pulse fuel pump as required.
Electric fuel pump is faulty - Change electric fuel pump as required.
ECM failure - Change electronic control modul.
| Engine starts but immediately shuts off |
Spark plug is faulty - Change spark plug.
Faulty ignition coil - Install a new ignition coil.
Damaged pulse fuel pump - Change pulse fuel pump as required.
Fuel system is clogged - Service fuel system.
Final fuel filter is clogged - Final filter needs changing.
Electric fuel pump failure - Install new electric fuel pump.
| Engine runs intermittently |
Ignition system problems - Test ignition and replace failed parts.
Dirty or defective fuel pump - Service or change fuel pump.
Fuel lines clogging - Service fuel lines.
Clogged fuel filter - Replace or clean fuel filter.
Engine is running overloaded - Reduce load.
Bad ignition timing - Adjust ignition timing as required.
Thermostat is defective - Replace thermostat.
Defective water pump - Install new water pump.
Stale gasoline - Use proper gasoline.
Excessive engine load - Reduce load.
Incorrectly adjusted low idle speed - Correct the settings.
Clogged or damaged fuel pump - Service or replace fuel pump.
Worn main bearings or crankshaft - Worn parts replacement required.
Piston rings or cylinder bore are worn - Replace faulty components.
Fuel pump is damaged or dirty - Service or replace fuel pump.
Ignition system failure - Inspect ignition system and change failed components.
Powerhead components are faulty - Defective parts need to be replaced.
Stator, coil, or switch box defective - Change damaged parts.
Compression is insufficient - Correct.
Fuel supply problem - Check fuel system.
Manifold is leaking - Repair leaks.
Vapor separator is flooded - Normalize vapor separator functions.
Defective or loose spark plug - Change or re-tighten spark plug.
Sleeve, piston, or rings are damaged - Change faulty parts.
Engine overloaded - Reduce engine load.
Clogged or defective fuel injectors - Service or replace fuel injectors.
| Motor vibrates excessively |
Propeller bent or damaged - Have propeller repaired or replaced.
Propeller shaft malfunction - Propeller shaft needs to be replaced.
Weeds wraped around propeller - Remove weeds from propeller.
Engine mounting bolt is not tightened - Tighten the bolt as required.
Loose or faulty steering pivot - Tighten or replace.
Propeller bent or damaged - Replace propeller.
Damaged propeller shaft - Replace propeller shaft.
Weeds wraped around propeller - Remove weeds from propeller.
Engine mounting bolt is not tightened - Tighten the bolt as required.
| Trim motor runs but system does not move |
Low oil level - Check oil level and add oil as required.
Pump assembly is damaged - Test pump and change if necessary.
Leakage of manual release valve - Valve need to be closed or changed.
Faulty pump driveshaft or motor - Replace defective component.
| Trim does not fully up or down |
Pump assembly is faulty - Change pump.
Tilt ram piston ball is displaced - Clean or repair.
Tilt ram piston O-ring is worn - Replace O-ring.
Oil level is insufficient - Checking oil level and add if necessary.
Lower check valve not seating in port side trim ram - Secure valve properly.
____________________________________________________________________________________
| Outboard Engines Technical Specifications |
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Industrial Engines Technical Specifications |
