Evinrude Ocean Pro 175 Problems
| Engine Model: Evinrude Ocean Pro 175 |
| Engine Type: 2-stroke 6-cylinder gasoline outboard engine |
| Total Displacement: 158.2 cu.in (2.6 L) |
| Rated Engine Power: 175 Hp (130 kW) at 6000 rpm |
| Fuel System: Two-barrel carburetors or direct fuel injection (DFI) |
____________________________________________________________________________________
| Engine difficult to start or will not start |
Fuel tank is empty - Fill fuel up.
Wrong grade of gasoline - Use quality gasoline.
Dirty fuel system - Check and clean.
Defective spark plug wire connection - Check spark plug wiring connection, repair or change.
Spark plug is defective - Spark plug need to be replaced.
Fuel filter is plugged - Replace or clean fuel filter.
Carburetor is clogged - Clean the carburetor.
Fuel lines clogging - Service fuel lines.
Closed or restricted fuel tank air vent - Open or service air vent.
Low fuel pump pressure - Install new fuel pump or rebuild it.
Damaged or worn fuel reed valve - Replace reed valve.
| Engine stops after starting |
Faulty spark plug - Replace spark plug.
Carburetor is dirty or faulty - Service or repair carburetor.
Defective ignition coil - Replace ignition coil as necessary.
Closed or restricted fuel tank air vent - Open or clean air vent.
Fuel pump pressure is low - Install new fuel pump or rebuild it.
Ignition failure - Inspect ignition system and change failed components.
Clogged or defective fuel pump - Test fuel pump and replace if necessary.
Carburetor components worn out - Repair or replace parts.
Fuel lines clogging - Service fuel lines.
Fuel tank air vent closed or restricted - Open or clean air vent.
Fuel filter is plugged - Change fuel filter.
Worn gaskets - Change gaskets.
Excessive engine load - Reduce engine load.
Carburetor fuel mixture is too lean - Use proper settings.
Incorrect ignition timing - Ignition timing needs to be set properly.
Thermostat is defective - Change thermostat as required.
Damaged water pump - Change water pump.
Incorrect propeller selection - Replace propeller.
Propeller bent or damaged - Have propeller repaired or replaced.
Outboard motor is mounted too high or too low - Position the engine correctly.
Low octane fuel - Change fuel.
Engine overloaded - Load reducing required.
Low idle speed set incorrectly - Correct idle settings.
Fuel pump is faulty or clogged - Test fuel pump and change if necessary.
Worn main bearings or crankshaft - Need to install new components.
Damaged cylinder bore or piston rings - Change faulty components.
Carburetor is improperly adjusted or dirty - Service or correctly adjust carburetor.
Dirty or defective fuel pump - Clean or install new fuel pump.
Defective ignition system - Check ignition and replace faulty components.
Damaged gaskets - Install new gaskets.
Powerhead parts are worn out - Replace defective components as required.
Propeller pitch or diameter incorrect - Check the propeller size.
Propeller bent or damaged - Have propeller repaired or replaced.
Motor mounted at incorrect height on transom - Adjust the outboard motor height correctly.
Trim angle is incorrect - Adjust trim angle correctly.
| Excessive fuel consumption |
Incorrect carburetor main jet adjustment - Adjust it correctly.
Spark plug is loose or defective - Tighten or change the spark plug.
Worn sleeve, rings, or piston - Change defective parts.
| Excessive motor vibration |
Damaged or improper size of propeller - Replace propeller.
Propeller shaft malfunction - Replace propeller shaft.
Weeds clogs the propeller - Clean the propeller.
Motor mounting bolt is loose - Tighten the bolt as required.
Loose or faulty steering pivot Tighten correctly or replace.
| Starter motor is not working |
Low battery power - Charge the battery.
Battery is not holding charge - Service charging system or replace battery.
Bad battery terminals or disconnected wiring - Connect wiring properly or install new terminals.
Damaged starter motor - Starter should be changed.
| Trim motor is running but trim system cannot move up or down |
Oil level is insufficient - Checking oil level and add if necessary.
Pump assembly is defective - Inspect pump and change as required.
Manual shut-off valve leaks - Close the valve or change it.
Faulty pump driveshaft or motor - Change defective component.
| Trim does not fully up or down |
Pump assembly faulty - Change pump.
Tilt ram piston ball is not positioned correctly - Clean or repair.
Damaged tilt ram piston O-ring - Install new O-ring.
Insufficient oil - Fill up oil.
Lower check valve is not properly secured in port side trim ram - Install valve correctly.
____________________________________________________________________________________
| Outboard Engines Technical Specifications |
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Industrial Engines Technical Specifications |
