Evinrude 150 Ficht Ram Troubleshooting
| Engine Model: Evinrude Ficht 150 |
| Engine Type: 2-stroke 6-cylinder gasoline outboard engine |
| Total Displacement: 158 cu.in (2.6 L) |
| Rated Engine Power: 150 Hp (111 kW) at 5000 rpm |
| Fuel System: Direct fuel injection (DFI) |
____________________________________________________________________________________
| Engine doesn't start or starts hard |
No fuel in fuel tank - Fill gasoline up.
Wrong grade of gasoline - Use correct fuel grade.
Air in fuel tank - Bleed fuel tank.
Spark plug wire is disconnected or loose - Check spark plug wiring connection, repair or change.
Spark plug is defective - Install new spark plug.
Dirty fuel filter - Change fuel filter.
Clogged fuel lines - Fuel lines need to be cleaned.
Fuel pressure is low - Inspect low pressure fuel pump or inspect fuel system for leaks.
Low air pressure - Check air system components.
Bad harness connections - Check wiring harness connections.
Ignition system is damaged - Check ignition components and replace if necessary.
Damaged fuel feed pump - Install new fuel feed pump.
Dirty or faulty fuel injector - Clean or install new injector.
ECM is not functioning - Replace ECM.
Reed valve is worn or damaged - Replace reed valve.
| Engine stops after starting |
Spark plug is damaged - Spark plug need to be replaced.
Faulty ignition coil - Ignition coil should be replaced.
Pulse pump is faulty - Change fuel pump as required.
Fuel system is dirty - Service fuel system.
Clogged fuel filter - Install new filter.
Ignition system failure - Inspect ignition system and change failed components.
Spark plug is damaged - Change spark plug as required.
Fuel pump is damaged or dirty - Check fuel pump and replace if necessary.
Low air pressure - Check air system components.
Dirt in the fuel lines - Clean fuel lines.
Fuel filter is plugged - Install new filter.
Direct injector is faulty - Replace as required.
Engine is overloaded - Reduce the load.
Incorrect ignition timing - Ignition timing needs to be set properly.
Defective thermostat - Change thermostat.
Water pump failure - Water pump need to be replaced.
Improper propeller diameter or pitch - Replace propeller.
Damaged or improper size of propeller - Replace propeller.
Outboard engine is positioned too low or too high - Mount the motor as required.
Low octane gasoline - Use correct fuel.
Engine is running overloaded - Load reducing required.
Too low idle RPM - Need to adjust idle speed.
Dirty or damaged fuel pump - Service or change fuel pump.
Main bearings or crankshaft failure - Repair or replace defective parts.
Piston rings or cylinder bore are damaged - Change defective parts.
Fuel pump is clogged or faulty - Clean or install new fuel pump.
Ignition system malfunction - Inspect ignition system and change failed components.
Worn powerhead parts - Replace defective parts as required.
Fuel pressure is low - Inspect low pressure fuel pump or inspect fuel system for leaks.
Low air pressure - Inspect air system for leaks.
Low compression - Correct it.
Fuel supply problem - Check fuel system.
Fuel regulator is leaking - Leak must be repaired.
Fuel filter is plugged - Replace or clean fuel filter.
Fuel injector is faulty or clogged - Clean or replace as required.
Manifold is leaking - Repair leaks.
Improper propeller diameter or pitch - Replace propeller.
Damaged or improper size of propeller - Replace propeller.
Outboard engine mounting height improperly - Have motor adjusted to proper transom height.
Trim angle is incorrect - Make the correct trim angle adjustment.
| Engine using too much gasoline |
Loose or defective spark plug - Change or re-tighten spark plug.
Rings, sleeve, or piston are damaged - Replace defective parts.
Excessive engine load - Reduce the load.
Dirty or defective fuel injectors - Service or change fuel injectors.
| Engine vibrates excessively |
Damaged or improper size of propeller - Replace propeller.
Damaged propeller shaft - Propeller shaft needs to be replaced.
Weeds in the propeller - Remove and clean propeller.
Motor mounting bolt is loose - Tighten bolt.
Steering pivot is loose or damaged - Tighten correctly or replace.
Damaged or improper size of propeller - Have propeller repaired or replaced.
Damaged propeller shaft - Have propeller shaft replaced.
Weeds clogs the propeller - Remove weeds from propeller.
Motor mounting bolt is loose - Tighten bolt.
| Trim motor runs but trim system does not move up or down |
Not enough oil - Fill up oil to required level.
Defective pump assembly - Test pump and change if necessary.
Leakage of manual drain valve - Close the valve fully or replace it.
Pump driveshaft or motor damaged - Replace worn component.
| Trim does not fully up or down |
Pump assembly is damaged - Change pump as required.
Tilt ram piston ball is not positioned correctly - Clean or repair.
Tilt ram piston O-ring is worn - Change O-ring.
Not enough oil - Fill up oil.
Lower check valve not seating in port side trim ram - Secure valve properly.
____________________________________________________________________________________
| Outboard Engines Technical Specifications |
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Industrial Engines Technical Specifications |
