Evinrude 225 ETEC Troubleshooting
| Engine Model: Evinrude E-TEC 225 |
| Engine Type: 2-stroke 6-cylinder gasoline outboard engine |
| Total Displacement: 210 cu.in (3.4 L) |
| Rated Engine Power: 225 Hp (168 kW) at 6000 rpm |
| Fuel System: Direct fuel injection (DFI) |
____________________________________________________________________________________
| Engine hard to start or will not start |
No gasoline in tank - Fill gasoline up.
Improper fuel grade - Use quality fuel.
Air or water in fuel system - Remove water or air from fuel system.
Loose or disconnected spark plug wire - Inspect spark plug wiring connection, change or repair.
Defective spark plug - Replace spark plug.
Plugged fuel filter - Replace fuel filter.
Restricted fuel lines - Clean fuel system lines.
Fuel pressure is low - Inspect low pressure fuel pump or inspect fuel system for leaks.
Air pressure is low - Inspect air system for leaks.
Damaged wiring harness connections - Inspect harness connections.
Ignition system is damaged - Check ignition system components and change if necessary.
Defective fuel feed pump - Change fuel feed pump.
Dirty or faulty fuel injector - Clean or replace if necessary.
Electronic control modul is not operating - Install new ECM.
Damaged or worn fuel reed valve - Install new reed valve.
| Engine stalls after starting |
Damaged spark plug - Change spark plug as required.
Ignition coil is not working - Ignition coil should be replaced.
Defective fuel pump - Change fuel pump.
Restrictions in fuel system - Service fuel system.
Fuel filter is clogged - Replace or clean filter.
Defective ignition - Inspect ignition system and change failed components.
Spark plug is faulty - Spark plug need to be replaced.
Fuel pump is damaged or dirty - Clean or replace fuel pump.
Low air pressure - Check air system components.
Fuel lines clogging - Clean fuel lines.
Fuel filter is dirty - Change fuel filter.
Faulty direct injector - Replace if necessary.
Engine is overloaded - Reduce load.
Ignition timing is wrong - Set the ignition timing correctly.
Thermostat is defective - Thermostat need to be replaced.
Faulty water pump - Water pump need to be replaced.
Propeller selection improperly - Install correct propeller.
Damaged or bent propeller - Have propeller repaired or replaced.
Outboard engine is positioned too low or too high - Mount the motor as required.
Stale fuel - Change gasoline.
Engine overloaded - Reduce load.
Low idle speed adjustment is incorrect - Correct the settings.
Fuel pump is defective or dirty - Service or change fuel pump.
Worn crankshaft or main bearings - Replace crankshaft or bearings.
Cylinder bore or piston rings are damaged - Change faulty parts.
Fuel pump is dirty or defective - Check fuel pump and replace if necessary.
Defective ignition system - Inspect ignition system and change failed components.
Worn powerhead parts - Defective parts need to be replaced.
Fuel pressure is low - Inspect low pressure fuel pump or inspect fuel system for leaks.
Air pressure is low - Normalize air pressure.
Bad compression - Normalize compression.
Fuel supply problem - Check fuel system.
Fuel regulator is leaking - Repair leaks.
Clogged fuel filter - Install new filter.
Damaged or clogged fuel injector - Clean or replace as required.
Manifold is leaking - Repair leaks.
Incorrect propeller selection - Check the propeller size.
Damaged or bent propeller - Replace propeller.
Incorrect outboard motor mounting height - Adjust the engine to correct transom height.
Trim angle is incorrect - Adjust trim angle correctly.
| Excessive fuel consumption |
Spark plug is loose or defective - Spark plug need to be replaced or tightened.
Worn sleeve, piston, or rings - Change faulty components.
Engine overload - Load reducing is recommended.
Clogged or defective fuel injectors - Check fuel injectors and replace if necessary.
| Excessive motor vibration |
Damaged or bent propeller - Replace propeller.
Propeller shaft malfunction - Replace propeller shaft.
Weeds wraped around propeller - Clean the propeller.
Motor mounting bolt is loose - Tighten bolt.
Damaged or loose steering pivot - Tighten correctly or replace.
Damaged or bent propeller - Replace propeller.
Propeller shaft malfunction - Replace propeller shaft.
Weeds clogs the propeller - Clean the propeller.
Motor mounting bolt is loose - Tighten the bolt as required.
| Trim motor is running but trim system cannot move up or down |
Oil insufficient - Check oil level and add oil as required.
Damaged pump assembly - Check pump and replace if necessary.
Leakage of manual release valve - Close the valve or change it.
Faulty pump driveshaft or motor - Change worn component.
| Trim does not fully up or down |
Pump assembly faulty - Change pump.
Tilt ram piston ball is displaced - Clean or repair.
Tilt ram piston O-ring damaged - Install new O-ring.
Not enough oil - Checking oil level and add if necessary.
Lower check valve not seating in port side trim ram - Install valve correctly.
____________________________________________________________________________________
| Outboard Engines Technical Specifications |
| Small Engines Technical Specifications |
| Car Engines Technical Specifications |
| Industrial Engines Technical Specifications |
